mình mới học cái này.thực hành trên packet tracer nhưng mãi ko sao ping từ pc0 đến pc1 dc
R0
R1
mình làm vậy là ping mấy cái với nhau ko dc.gửi thử thư cũng ko xong
giúp mình nhé
R0
Continue with configuration dialog? [yes/no]: no
Press RETURN to get started!
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no sh
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#ex
Router(config)#int s0/0/0
Router(config-if)#ip add 172.168.2.1 255.255.0.0
Router(config-if)#no sh
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down
Router(config-if)#ex
Router(config)#ip route 192.168.2.0 255.255.255.0 172.168.2.2
Router(config)#ex
%SYS-5-CONFIG_I: Configured from console by console
Router#
Press RETURN to get started!
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no sh
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#ex
Router(config)#int s0/0/0
Router(config-if)#ip add 172.168.2.1 255.255.0.0
Router(config-if)#no sh
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down
Router(config-if)#ex
Router(config)#ip route 192.168.2.0 255.255.255.0 172.168.2.2
Router(config)#ex
%SYS-5-CONFIG_I: Configured from console by console
Router#
Continue with configuration dialog? [yes/no]: no
Press RETURN to get started!
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.2.1 255.255.255.0
Router(config-if)#no sh
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#ex
Router(config)#int s0/0/0
Router(config-if)#ip add 172.168.2.2 255.255.0.0
Router(config-if)#no sh
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
Router(config-if)#ex
Router(config)#ip route 192.168.1.0 255.255.255.0 172.168.2.1
Router(config)#ex
%SYS-5-CONFIG_I: Configured from console by console
Router#
Press RETURN to get started!
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.2.1 255.255.255.0
Router(config-if)#no sh
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#ex
Router(config)#int s0/0/0
Router(config-if)#ip add 172.168.2.2 255.255.0.0
Router(config-if)#no sh
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
Router(config-if)#ex
Router(config)#ip route 192.168.1.0 255.255.255.0 172.168.2.1
Router(config)#ex
%SYS-5-CONFIG_I: Configured from console by console
Router#
giúp mình nhé
Comment