• If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Xin chào ! Nếu đây là lần đầu tiên bạn đến với diễn đàn, xin vui lòng danh ra một phút bấm vào đây để đăng kí và tham gia thảo luận cùng VnPro.

Announcement

Collapse
No announcement yet.

Hỏi lab về advandSTP???

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Hỏi lab về advandSTP???

    Xin hỏi ai đã luyện lab trong phẩn advandSTP, có sơ đồ lab nào cho mình với. Chân thành cám ợn

  • #2
    RE: Hỏi lab về advandSTP???

    Bài Viết về MSTP và RSTP do Nguyễn Anh Hào thực hiện, nguồn http://chuyenviet.com

    I/Tổng quan :

    Mục tiêu của bài viết này là xem các thực thi MSTP của Switch , qua đó chúng ta có thể thử được sự hoạt động của RSTP bằng cách nối thêm 1 đường fa0/5 của Sw3 vào Sw1 . Như vậy trong bài lab này chúng ta có thể được cả hai loại protocol trên


    II/Các bước cấu hình :
    Ta sử dụng 2 Switch 3550 và 2 Switch 2950 ,các Switch này đề nằm trong VTP doamin là vnpro , VTP mode của 2 Sw1 , Sw 2 là Server còn Sw3 là mode client .
    Bước 1 : Xoá cấu hình cũ Switch , khi khởi động vào
    Bước 2 : Cấu hình trunk giữa các Switch : ta cấu hình như sau
    Sw1(config)#int fa0/1
    Sw1(config-if)#switchport trunk encapsulation dot1q
    Sw1(config-if)#switchport mode trunk
    Sw1(config)#int fa0/3
    Sw1(config-if)#switchport trunk encapsulation dot1q
    Sw1(config-if)#switchport mode trunk

    Sw2(config)#int fa0/1
    Sw2(config-if)#switchport trunk encapsulation dot1q
    Sw2(config-if)#switchport mode trunk
    Sw2(config)#int fa0/3
    Sw2(config-if)#switchport trunk encapsulation dot1q
    Sw2(config-if)#switchport mode trunk
    Giống như Sw1, Sw2 . Sw3 cấu hình tương tự .
    Bước 3 : Bây giờ ta bắt đầu tạo các Vlan tại Sw1
    Trước khi cấu hình Vlan , ta cấu hình vtp mode của Sw1, Sw2 là server . Sw3 là client . Cả ba đều có domain là vnpro .
    Sw1#vlan database
    Sw1(vlan)#vtp m server
    Device mode already VTP SERVER.
    Sw1(vlan)#vtp do
    Sw1(vlan)#vtp domain vnpro
    Changing VTP domain name from NULL to vnpro
    Sw1(vlan)#apply
    APPLY completed.
    Sw1(vlan)#exit
    APPLY completed

    Sw2#vlan database
    Sw2(vlan)#vtp server
    Device mode already VTP SERVER.
    Sw2(vlan)#vtp do
    Sw2(vlan)#vtp domain vnpro
    Domain name already set to vnpro .
    Sw2(vlan)#apply
    APPLY completed.
    Sw2(vlan)#con exit
    APPLY completed.
    Exiting...
    Sw3#vlan database
    Sw3(vlan)#vtp client
    Setting device to VTP CLIENT mode.
    Sw3(vlan)#vtp domain vnpro
    Domain name already set to vnpro .
    Sw3(vlan)#apply
    Apply not allowed when device is in CLIENT state.

    Sau khi cấu hình vtp , ta cấu hình các vlan từ Switch 1 .
    Sw1(vlan)#vlan 10 name Accounting
    VLAN 10 added:
    Name: Accounting
    Sw1(vlan)#vlan 20 name Marketing
    VLAN 20 added:
    Name: Marketing
    Sw1(vlan)#vlan 30 nane Engineering
    VLAN 30 added:
    Name: Engineering
    Sw1(vlan)#vlan 49 name HumanResouce
    VLAN 40 added:
    Name: HumanResource
    Sw1(vlan)#vlan 50 name GraphicDesign
    VLAN 50 added:
    Name: GraphicDesign
    Sau đó kiểm tra các Vlan này bằng cách đánh lệnh show vlan tại các Switch
    Sw2#show vlan

    VLAN Name Status Ports
    ---- -------------------------------- --------- -------------------------------
    1 default active Fa0/2, Fa0/4, Fa0/5, Fa0/6
    Fa0/7, Fa0/8, Fa0/9, Fa0/10
    Fa0/11, Fa0/12, Fa0/13, Fa0/14
    Fa0/15, Fa0/16, Fa0/17, Fa0/18
    Fa0/19, Fa0/20, Fa0/21, Fa0/22
    Fa0/23, Fa0/24, Gi0/1, Gi0/2
    10 Accounting active
    20 Marketing active
    30 Engineering active
    40 HumanResource active
    50 GraphicDesign active
    1002 fddi-default active
    1003 token-ring-default active
    1004 fddinet-default active
    1005 trnet-default active

    Bước 4 : Chạy mặc định của Spanning tree là : Multiple spaning –tree sử dụng RSTP cho sự hội tụ tức thời . Mỗi instance hoạt động độc lập với instance khác . Cấu trúc này có thể cung cấp nhiều đường dẫn cho các traffic và chia tải .
    Sw1#show spanning-tree
    VLAN0001
    Spanning tree enabled protocol ieee
    Root ID Priority 32769
    Address 000d.299a.7e00
    This bridge is the root
    Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

    Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)
    Address 000d.299a.7e00
    Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
    Aging Time 300

    Interface Role Sts Cost Prio.Nbr Type
    ---------------- ---- --- --------- -------- --------------------------------
    Fa0/1 Desg FWD 19 128.1 P2p
    Fa0/3 Desg FWD 19 128.3 P2p
    Ta cấu hình MSTP trên Switch 1 , MSTP cho phép chúng ta nhóm các Vlan lại thành các Spanning-tree instance , các spanning tree khác số instance sẽ hoạt động đọc lập với nhau , giải pháp này là một giải pháp thực sự để chia tải vài giảm bớt được sự hoạt động quá nhiều của Spanning-tree . MSTP chỉ hỗ trợ 16 instance , các số instance từ 1 đến 15
    Từ config mode , vào mst config mode :

    Sw1(config)#spanning-tree mst configuration
    Sw1(config-mst)#instance 1 vlan 1-30
    Sw1(config-mst)#name vnpro
    Sw1(config-mst)#revision 10
    Dùng lệnh show pending để xem lại .
    Sw1(config-mst)#show pending
    Pending MST configuration
    Name [vnpro]
    Revision 10
    Instance Vlans mapped
    -------- ---------------------------------------------------------------------
    0 31-4094
    1 1-30
    Các mst có instance 1 là chứa các Vlan 1->30 , còn instance 0 chứa tất cả các vlan còn lại .
    Tương tự cấu hình cho các Sw2, Sw 3
    Sw2(config)#spanning-tree mst configuration
    Sw2(config-mst)#instance 1 vlan 1-30
    Sw2(config-mst)#name vnpro
    Sw2(config-mst)#revision 10
    Ta sử dụng show spanning-tree để xem hoạt động của các spanning-tree .
    MST00
    Spanning tree enabled protocol mstp
    Root ID Priority 32768
    Address 000d.299a.7e00
    This bridge is the root
    Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

    Bridge ID Priority 32768 (priority 32768 sys-id-ext 0)
    Address 000d.299a.7e00
    Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

    Interface Role Sts Cost Prio.Nbr Type
    ---------------- ---- --- --------- -------- --------------------------------
    Fa0/1 Desg FWD 200000 128.1 P2p
    Fa0/3 Desg FWD 200000 128.3 P2p

    MST01
    Spanning tree enabled protocol mstp
    Root ID Priority 32769
    Address 000d.299a.7e00
    This bridge is the root
    Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

    Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)
    Address 000d.299a.7e00
    Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

    Interface Role Sts Cost Prio.Nbr Type
    ---------------- ---- --- --------- -------- --------------------------------
    Fa0/1 Desg FWD 200000 128.1 P2p
    Fa0/3 Desg FWD 200000 128.3 P2p
    Cả hai MST00 và MST01 đều có root brigde là switch 1 , bây giờ ta cấu hình đối với MST00 thì root bridge là switch 2 .
    Sw2(config)#spanning-tree mst 0 root primary
    Dùng lệnh show spanning-tree để kiểm tra trên switch 2 lúc này .
    Sw2#show spanning-tree

    MST00
    Spanning tree enabled protocol mstp
    Root ID Priority 24576
    Address 000d.bd29.d080
    This bridge is the root
    Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

    Bridge ID Priority 24576 (priority 24576 sys-id-ext 0)
    Address 000d.bd29.d080
    Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

    Interface Role Sts Cost Prio.Nbr Type
    ---------------- ---- --- --------- -------- --------------------------------
    Fa0/1 Desg FWD 200000 128.1 P2p
    Fa0/3 Desg FWD 200000 128.3 P2p

    MST01
    Spanning tree enabled protocol mstp
    Root ID Priority 24577
    Address 000d.299a.7e00
    Cost 200000
    Port 3 (FastEthernet0/3)
    Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

    Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)
    Address 000d.bd29.d080
    Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

    Interface Role Sts Cost Prio.Nbr Type
    ---------------- ---- --- --------- -------- --------------------------------
    Fa0/1 Altn BLK 200000 128.1 P2p
    Fa0/3 Root FWD 200000 128.3 P2p

    Như vậy đối với MST00 thì Switch làm root và MST01 thì vẫn là Sw1 .
    Bước 5 : Thử RSTP . Bây giờ ta cắm port 5 của Sw1 với port 5 của Switch 3 , và sau đó cấu hình “ Trunk “ cho 2 port này .
    Sw1(config)#int fa0/5
    Sw1(config-if)#switchport trunk encapsulation dot1q
    Sw1(config-if)#switchport mode trunk

    Sw3(config)#int fa0/5
    Sw3(config-if)#switchport trunk encapsulation dot1q
    Sw3(config-if)#switchport mode trunk
    Sau khi cấu hình xong , ta show spanning-tree ở cả 2 Sw1, Sw3
    Sw3#show spanning-tree

    MST00
    Spanning tree enabled protocol mstp
    Root ID Priority 24576
    Address 000d.bd29.d080
    Cost 0
    Port 3 (FastEthernet0/3)
    Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

    Bridge ID Priority 32768 (priority 32768 sys-id-ext 0)
    Address 000d.bc33.2b00
    Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

    Interface Role Sts Cost Prio.Nbr Type
    ---------------- ---- --- --------- -------- --------------------------------
    Fa0/1 Altn BLK 200000 128.1 P2p
    Fa0/3 Root FWD 200000 128.3 P2p
    Fa0/5 Altn BLK 200000 128.5 P2p
    Sw1#show spanning-tree

    MST00
    Spanning tree enabled protocol mstp
    Root ID Priority 24576
    Address 000d.bd29.d080
    Cost 0
    Port 1 (FastEthernet0/1)
    Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

    Bridge ID Priority 32768 (priority 32768 sys-id-ext 0)
    Address 000d.299a.7e00
    Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

    Interface Role Sts Cost Prio.Nbr Type
    ---------------- ---- --- --------- -------- --------------------------------
    Fa0/1 Root FWD 200000 128.1 P2p
    Fa0/3 Desg FWD 200000 128.3 P2p
    Fa0/5 Desg FWD 200000 128.5 P2p

    --More--
    MST01
    Spanning tree enabled protocol mstp
    Root ID Priority 24577
    Address 000d.299a.7e00
    This bridge is the root
    Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

    Bridge ID Priority 24577 (priority 24576 sys-id-ext 1)
    Address 000d.299a.7e00
    Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

    Interface Role Sts Cost Prio.Nbr Type
    ---------------- ---- --- --------- -------- --------------------------------
    Fa0/1 Desg FWD 200000 128.1 P2p
    Fa0/3 Desg FWD 200000 128.3 P2p
    Fa0/5 Desg FWD 200000 128.5 P2p
    Bước tiếp theo ta dựt cáp của fa0/1 của Sw3 , lúc này root port sẽ không còn nữa , cổng fa0/5 sẽ chuyển lên làm root port . Do link type của các liên kết là ( fa0/5 ) là p2p , nên quá trình chuyển trạng thái sẽ bị rút gọn . Cổng fa0/5 sẽ chuyển trạng thái rất nhanh . Ta bật các lệnh debug spanning mst role và service timestamp trong mode config .
    Khi dựt cáp từ port 1 sw3
    Sw3#
    01:10:41: MSTP(1): Fa0/5 is now root port
    01:10:41: MSTP(1): Fa0/1 is now alternate port
    01:10:41: MSTP(0): updt roles
    01:10:42: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
    01:10:43: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to down
    Bây giờ ta cắm lại :
    Sw3#
    01:10:52: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
    01:10:53: MSTP(0): Fa0/1 is now designated
    01:10:53: MSTP(1): Fa0/1 is now designated portcam
    01:10:53: MSTP(0): updt roles
    01:10:53: MSTP(0): Fa0/1 is now alternate
    01:10:53: MSTP(1): Fa0/1 is now root port
    01:10:53: MSTP(1): Fa0/5 is now alternate port
    Translating "cam"...domain server (255.255.255.255)
    % Unknown command or computer name, or unable to find computer address
    Sw3#
    01:10:54: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up. Quá trình xảy ra rất nhanh , có thể dễ dàng theo dõi bằng các lệnh debug . Như vậy so với STP và RSTP ta thấy RSTP nhanh hơn và tiện lợi hơn .
    Email : vnpro@vnpro.org
    ---------------------------------------------------------------------------------------------------------------
Trung Tâm Tin Học VnPro
149/1D Ung Văn Khiêm P25 Q.Bình thạnh TPHCM
Tel : (08) 35124257 (5 lines)
Fax: (08) 35124314

Home page: http://www.vnpro.vn
Support Forum: http://www.vnpro.org
- Chuyên đào tạo quản trị mạng và hạ tầng Internet
- Phát hành sách chuyên môn
- Tư vấn và tuyển dụng nhân sự IT
- Tư vấn thiết kế và hỗ trợ kỹ thuật hệ thống mạng

Network channel: http://www.dancisco.com
Blog: http://www.vnpro.org/blog

Comment

    Working...
    X