• If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Xin chào ! Nếu đây là lần đầu tiên bạn đến với diễn đàn, xin vui lòng danh ra một phút bấm vào đây để đăng kí và tham gia thảo luận cùng VnPro.

Announcement

Collapse
No announcement yet.

CCNA Access List Sim

Collapse
This is a sticky topic.
X
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • CCNA Access List Sim

    Question
    An administrator is trying to ping and telnet from Switch to Router with the results shown below:
    Switch>
    Switch> ping 10.4.4.3
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 10.4.4.3,timeout is 2 seconds:
    .U.U.U
    Success rate is 0 percent (0/5)
    Switch>
    Switch> telnet 10.4.4.3
    Trying 10.4.4.3 …
    % Destination unreachable; gateway or host down
    Switch>
    Click the console connected to Router and issue the appropriate commands to answer the questions.
    Answer and Explanation:


    For this question we only need to use the show running-config command to answer all the questions below
    Router>enable
    Router#show running-config
    Question 1:
    Which will fix the issue and allow ONLY ping to work while keeping telnet disabled?
    A – Correctly assign an IP address to interface fa0/1
    B – Change the ip access-group command on fa0/0 from “in” to “out”
    C – Remove access-group 106 in from interface fa0/0 and add access-group 115 in.
    D – Remove access-group 102 out from interface s0/0/0 and add access-group 114 in
    E – Remove access-group 106 in from interface fa0/0 and add access-group 104 in


    Answer: E


    Explanation:
    Let’s have a look at the access list 104:
    The question does not ask about ftp traffic so we don’t care about the two first lines. The 3rd line denies all telnet traffic and the 4th line allows icmp traffic to be sent (ping). Remember that the access list 104 is applied on the inbound direction so the 5th line “access-list 104 deny icmp any any echo-reply” will not affect our icmp traffic because the “echo-reply” message will be sent over the outbound direction.
    Question 2:
    What would be the effect of issuing the command ip access-group 114 in to the fa0/0 interface?
    A – Attempts to telnet to the router would fail
    B – It would allow all traffic from the 10.4.4.0 network
    C – IP traffic would be passed through the interface but TCP and UDP traffic would not
    D – Routing protocol updates for the 10.4.4.0 network would not be accepted from the fa0/0 interface


    Answer: B
    Explanation:
    From the output of access-list 114: access-list 114 permit ip 10.4.4.0 0.0.0.255 any we can easily understand that this access list allows all traffic (ip) from 10.4.4.0/24 network
    Question 3:
    What would be the effect of issuing the command access-group 115 in on the s0/0/1 interface?
    A – No host could connect to Router through s0/0/1
    B – Telnet and ping would work but routing updates would fail.
    C – FTP, FTP-DATA, echo, and www would work but telnet would fail
    D – Only traffic from the 10.4.4.0 network would pass through the interface


    Answer: A
    Explanation:
    First let’s see what was configured on interface S0/0/1:
    Recall that each interface only accepts one access-list, so when using the command “ip access-group 115 in” on the s0/0/1 interface it will overwrite the initial access-list 102. Therefore any telnet connection will be accepted (so we can eliminate answer C).
    B is not correct because if telnet and ping can work then routing updates can, too.
    D is not correct because access-list 115 does not mention about 10.4.4.0 network. So the most reasonable answer is A.

    But here raise a question…
    The wildcard mask of access-list 115, which is 255.255.255.0, means that only host with ip addresses in the form of x.x.x.0 will be accepted. But we all know that x.x.x.0 is likely to be a network address so the answer A: “no host could connect to Router through s0/0/1” seems right…
    But what will happen if we don’t use a subnet mask of 255.255.255.0? For example we can use an ip address of 10.45.45.0 255.255.0.0, such a host with that ip address exists and we can connect to the router through that host. Now answer A seems incorrect!
    Phạm Minh Tuấn

    Email : phamminhtuan@vnpro.org
    Yahoo : phamminhtuan_vnpro
    -----------------------------------------------------------------------------------------------
Trung Tâm Tin Học VnPro
149/1D Ung Văn Khiêm P25 Q.Bình thạnh TPHCM
Tel : (08) 35124257 (5 lines)
Fax: (08) 35124314

Home page: http://www.vnpro.vn
Support Forum: http://www.vnpro.org
- Chuyên đào tạo quản trị mạng và hạ tầng Internet
- Phát hành sách chuyên môn
- Tư vấn và tuyển dụng nhân sự IT
- Tư vấn thiết kế và hỗ trợ kỹ thuật hệ thống mạng

Network channel: http://www.dancisco.com
Blog: http://www.vnpro.org/blog
Working...
X