• If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Xin chào ! Nếu đây là lần đầu tiên bạn đến với diễn đàn, xin vui lòng danh ra một phút bấm vào đây để đăng kí và tham gia thảo luận cùng VnPro.

Announcement

Collapse
No announcement yet.

Làm sao để đổi password Router?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • #31
    RE: Làm sao để đổi password Router?

    Hi Notme!

    Nếu bạn đang dùng Router của Cisco, mình có một số ý sau:

    1. Các IOS của Cisco Router thường dùng thuật ngữ "reload" để chỉ quá trình khởi đông lại của Router.

    2. Các IOS của Cisco Router nói chung đều cho phép người sử dụng xây dựng các password và hiệu chỉnh hoặc thay đổi chúng nếu cần thiết.

    3. Tùy theo loại password chúng ta đang quan tâm là gì, sẽ có những syntax và mode cấu hình tương ứng. Ở trên mính thấy có đề cập rùi đó.

    4. Tuy nhiên, các hiệu chỉnh và thay đổi này sẽ được lưu vào RAM của Router và chỉ có giá trị trong một phiên tương tác nào đó với Router mà thui. Để có thể duy trì kết quả này cho các phiên làm việc sau, bạn cần lưu chúng vào NVRAM bằng command copy run start

    5. Nhung cũng có đôi lúc bạn đã lưu chúng vào NVRAM, reload lại Router và thấy không có sự thay đổi nào xảy ra thì thường là do giá trị thanh ghi của ROuter đã bắt nó phải bỏ qua các cấu hình trong NVRAM (startup-config), trong đó có cái pass vừa thay đổi của chúng ta

    Bạn có thể dành chút thời gian để đến với link

    để xem qua các bài viết về phần này nhe

    Còn nếu bạn dùng các Router của hãng khác thì mọi thay đổi và hiệu chỉnh thường chỉ có hiệu lực sau khi bạn đã "reboot" lại thiết bịt

    Thân mến
    Vietnamese Professionals (VnPro)
    Tel: +84 8 5124257 - 5125314
    Fax: +84 8 5124314
    149/1D Ung Văn Khiêm, P25, Q. Bình Thạnh
    Tp.Ho Chi Minh
    http://www.chuyenviet.com

    VnPro - The way to get knowledge

    Comment


    • #32
      RE: Làm sao để đổi password Router?

      cho hoi enable password và enable secret khác nhau như thế nào?

      Cảm ơn, chúc vui vẹ

      Comment


      • #33
        RE: Làm sao để đổi password Router?

        Trong router thường có các loại password sau:

        enable password: đề vào chế độ enable mode
        line password: dùng để giới hạn truy cập thông qua các line của router.
        các password của user: dùng trong qúa trình xác thực.

        secret password là loại password mà có thể sử dụng được cho tất cả các trường hợp nêu trên. Một người khi nắm dược secret password sẽ có thể dùng nó để thay thế tất cả các loại pass trên.

        Comment


        • #34
          RE: Làm sao để đổi password Router?

          router có 2 loại password để vào Privilege Mode:
          1.enable secret
          2.enable password
          Nếu chúng ta set cùng lúc 2 password này thi router sẽ ưu tiên sử dụng enable secret khi truy nhập vào Privilege Mode(enable password bị disable).Enable password chỉ được sử dụng nếu ta ko set enable secret.
          -Enable secret được mã hóa bằng MD5
          -Enable password mặc định ko được mã hóa (password này có thể thấy được trong file cấu hình được save trong NVRAM,o chế độ default).Ma hóa enable password bằng lệnh:
          Router(config)#service password-encryption
          Để tìm lại enable password bị mất thì dùng tool
          Khi đa bị mất secret password,muon set lại secret password thi vào chế độ bootrap,su dụng lệnh confreg ......

          Comment


          • #35
            RE: Làm sao để đổi password Router?

            icare thử dùng lệnh no service password-encryption, sau đó reload lại router thử xem có được không???
            Chúc thành cộng

            Comment


            • #36
              RE: Làm sao để đổi password Router?

              a ha!! mình quên mất cái lệnh no service password-encryption.Cam on bạn đã nhắc mình nha!Nhung nếu ko có enable password thì làm sao vào Privilege mode để đánh lệnh Router(config)#no service password-encryption nhỉ?hơ hơ hơ!!!Giong như 1 kẻ trộm sau khi đa đột nhập vào nhà được rồi thì lại đi tìm chìa khóa để mở cửa vô nhà vậy !!! :)

              Comment


              • #37
                RE: Làm sao để đổi password Router?

                - nếu bạn là chủ router thì không có vấn đề gì
                + TH1 : Khi bạn có password để telnet vào router rồi thì làm như các bạn kia đã mô tả :
                >enable
                >nhap pass vào
                #conf t
                (config-line)#line vty 0 4
                (config-line)#login
                (config-line)#password Yourpass
                (config-line)#exit
                #copy run star
                #reload
                nếu bạn bị mất điện khi đang cấu hình thì cấu hình đó sẽ mất chứ ko phải là reload như bạn nghị
                + TH2 : nếu bạn bị mất password enable thì phải thực hiện Recover password trình tự hơi dài dòng một chút.
                Dổi giá trị thanh ghi thành 0x2142 (>confreg 0x2142)để router bỏ qua file cấu hình trong NVRAM,sau đó vào router :copy star -->run và sửa password.
                Sau khi sửa pass thì copy run-->star,doi lại giá trị thanh ghi thành 0x2102 và reload lại router.
                Chúc bạn thành công

                Comment


                • #38
                  RE: Làm sao để đổi password Router?

                  Xin chào!
                  không biết là ông notme đã làm được chưa vậy? Tui thấy ông hỏi có vẻ biết mà cũng có vẻ là không biết thưc. Ông có phá người ta không đấy :P
                  Nếu chưa làm được thì tôi chỉ cách làm cho, đến tận nhà hướng dẫn luôn :P
                  Chào nhé!

                  Comment


                  • #39
                    Doi password khi telnet

                    Nếu bạn đã biết pasword telnet cũ thì việc đổi nó lại không có gì khó cả
                    Ban làm như sau :

                    telnet x.x.x.x
                    !Nhap pass
                    enable
                    !nhap pass
                    config t
                    line vty 0 4
                    password NEWPASS
                    login

                    exit

                    write

                    Còn nếu bạn không nhớ password ( hoặc không biết pass mà muốn hack ) thì pó tay.
                    Vì bạn không thể dùng telnet để recover password được.
                    Bạn chỉ có thể recover pass khi kết nối console và phải bật và tắt Router.
                    Le Vinh Phuc
                    The easiest way to master in Network is to learn as much as posible, do as much as posible

                    Comment


                    • #40
                      Bạn phải Write mem thì mới lưu được chứ

                      Comment


                      • #41
                        write va write mem co tac dung nhu nhau. ko tin kiem con router nao ma thu.

                        nghe chung cai viec doi pass telnet cua ong notme vat va qua. cac huong dan deu dung ca day, neu ko lam dc thi hinh nhu dang tim cach chui vao con router nao do de pha day :)

                        Comment


                        • #42
                          Trong trường hợp nào đó lỡ ta quên mất password thì phải làm thế nào?:rolleyes:

                          Comment


                          • #43
                            nếu lỡ quên password:
                            1 - nếu chưa write mem --> restart lại router
                            2 - nếu đã write mem --> thực hiện các bước password recovery

                            Comment


                            • #44
                              Tui de nghi cách như sau, ban thử làm xem nha. http://www.cisco.com/en/US/products/...80094675.shtml
                              Ban vao trang đó đi, đây là cách bạn config từ cổng consol
                              chuc thanh cong!

                              Comment


                              • #45
                                Sợ ông kô bít cách xem, nên tui copy lun ra đây
                                Step-by-Step Procedure
                                To recover your password, complete these steps:

                                Attach a terminal or PC with terminal emulation to the console port of the router.

                                Use these terminal settings:

                                9600 baud rate

                                No parity

                                8 data bits

                                1 stop bit

                                No flow control

                                For more information on cabling, and details about how to connect a terminal to the console port or the AUX port, visit these links:

                                Cabling Guide for Console and AUX Ports on Cisco Routers

                                Connect a Terminal to Catalyst 2948G-L3, 4908G-L3, and 4840G Series Switches

                                Catalyst 8510CSR, and 8540CSR Switches Console Port Pinouts

                                If you still have access to the router, type show version , and record the setting of the configuration register. It is usually 0x2102 or 0x102.

                                For a sample output of the show version command, refer to the Example of Password Recovery Procedure section.

                                If you do not have access to the router (because of a lost login or TACACS password), you can safely consider that your configuration register is set to 0x2102.

                                Use the power switch to turn off the router, and then turn it back on.

                                Important: To simulate step 4 on a Cisco 6400, pull out and then replace the Node Route Processor (NRP) or Node Switch Processor (NSP) card.

                                Important: To simulate step 4 on a Cisco 6x00 using NI-2, pull out and then replace the NI-2 card.

                                Press Break on the terminal keyboard within 60 seconds of the power-up to put the router into ROMMON.

                                If the break sequence does not work, see Standard Break Key Sequence Combinations During Password Recovery for other key combinations.

                                Type confreg 0x2142 at the rommon 1> prompt to boot from Flash without loading the configuration.

                                Type reset at the rommon 2> prompt.

                                The router reboots but ignores its saved configuration.

                                Type no after each setup question or press Ctrl-C to skip the initial setup procedure.

                                Type enable at the Router> prompt.

                                You are taken to the enable mode, and the Router# prompt appears.

                                Important: Type configure memory or copy startup-config running-config to copy the nonvolatile RAM (NVRAM) into memory.

                                Do not type configure terminal .

                                Type write terminal or show running-config .

                                The show running-config and write terminal commands show the configuration of the router. In this configuration you see under all the interfaces the shutdown command, which means all interfaces are currently shutdown. Also, you can see the passwords (enable password, enable secret, vty, console passwords, and so on) either in encrypted or unencrypted format. The unencrypted passwords can be re-used, the encrypted ones will have to be changed with a new one.

                                Type configure terminal and make the changes.

                                The prompt is now hostname(config)#.

                                Type enable secret <password> to change the enable secret password, for example.

                                Issue the no shutdown command on every interface that is used.

                                If you issue a show ip interface brief command, every interface that you want to use should be "up up".

                                Type config-register 0x2102, or the value you recorded in step 2.

                                Press Ctrl-Z or end to leave the configuration mode.

                                The prompt is now changed to hostname#.

                                Type write memory or copy running-config startup-config to commit the changes.

                                Example of Password Recovery Procedure
                                The example in this section presents an actual password recovery procedure. We used a Cisco 2600 to create this example. Even if you do not use a Cisco 2600, this example will be almost exactly what you experience on your product.

                                Router>enable
                                Password:
                                Password:
                                Password:
                                % Bad secrets

                                Router>show version
                                Cisco Internetwork Operating System Software
                                IOS (tm) C2600 Software (C2600-IS-M), Version 12.0(7)T, RELEASE SOFTWARE (fc2)
                                Copyright (c) 1986-1999 by cisco Systems, Inc.
                                Compiled Tue 07-Dec-99 02:21 by phanguye
                                Image text-base: 0x80008088, data-base: 0x80C524F8

                                ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)

                                Router uptime is 3 minutes
                                System returned to ROM by abort at PC 0x802D0B60
                                System image file is "flash:c2600-is-mz.120-7.T"

                                cisco 2611 (MPC860) processor (revision 0x202) with 26624K/6144K bytes of memory.
                                Processor board ID JAB031202NK (3878188963)
                                M860 processor: part number 0, mask 49
                                Bridging software.
                                X.25 software, Version 3.0.0.
                                Basic Rate ISDN software, Version 1.1.
                                2 Ethernet/IEEE 802.3 interface(s)
                                2 Serial(sync/async) network interface(s)
                                1 ISDN Basic Rate interface(s)
                                32K bytes of non-volatile configuration memory.
                                8192K bytes of processor board System flash partition 1 (Read/Write)
                                8192K bytes of processor board System flash partition 2 (Read/Write)

                                Configuration register is 0x2102

                                Router>


                                !--- The router was just powercycled and during bootup a
                                !--- break sequence was sent to the router.

                                !

                                *** System received an abort due to Break Key ***

                                signal= 0x3, code= 0x500, context= 0x813ac158
                                PC = 0x802d0b60, Vector = 0x500, SP = 0x80006030
                                rommon 1 > confreg 0x2142

                                You must reset or power cycle for new config to take effect

                                rommon 2 > reset

                                System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
                                Copyright (c) 1999 by cisco Systems, Inc.
                                TAC:Home:SW:IOS:Specials for info
                                C2600 platform with 32768 Kbytes of main memory


                                program load complete, entry point: 0x80008000, size: 0x6fdb4c

                                Self decompressing the image : ###############################
                                ################################################## ############
                                ################################################## ############
                                ################################################## ############
                                ############################### [OK]


                                Restricted Rights Legend

                                Use, duplication, or disclosure by the Government is
                                subject to restrictions as set forth in subparagraph
                                (c) of the Commercial Computer Software - Restricted
                                Rights clause at FAR sec. 52.227-19 and subparagraph
                                (c) (1) (ii) of the Rights in Technical Data and Computer
                                Software clause at DFARS sec. 252.227-7013.

                                cisco Systems, Inc.
                                170 West Tasman Drive
                                San Jose, California 95134-1706

                                Cisco Internetwork Operating System Software
                                IOS (tm) C2600 Software (C2600-IS-M), Version 12.0(7)T, RELEASE SOFTWARE (fc2)
                                Copyright (c) 1986-1999 by cisco Systems, Inc.
                                Compiled Tue 07-Dec-99 02:21 by phanguye
                                Image text-base: 0x80008088, data-base: 0x80C524F8

                                cisco 2611 (MPC860) processor (revision 0x202) with 26624K/6144K bytes of memory.
                                Processor board ID JAB031202NK (3878188963)
                                M860 processor: part number 0, mask 49
                                Bridging software.
                                X.25 software, Version 3.0.0.
                                Basic Rate ISDN software, Version 1.1.
                                2 Ethernet/IEEE 802.3 interface(s)
                                2 Serial(sync/async) network interface(s)
                                1 ISDN Basic Rate interface(s)
                                32K bytes of non-volatile configuration memory.
                                8192K bytes of processor board System flash partition 1 (Read/Write)
                                8192K bytes of processor board System flash partition 2 (Read/Write)


                                --- System Configuration Dialog ---

                                Would you like to enter the initial configuration dialog? [yes/no]: n

                                Press RETURN to get started!

                                00:00:19: %LINK-3-UPDOWN: Interface BRI0/0, changed state to up
                                00:00:19: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
                                00:00:19: %LINK-3-UPDOWN: Interface Ethernet0/1, changed state to up
                                00:00:19: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down
                                00:00:19: %LINK-3-UPDOWN: Interface Serial0/1, changed state to down
                                00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0,
                                changed state to down
                                00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0,
                                changed state to up
                                Router>
                                00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/1,
                                changed state to up
                                00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0,
                                changed state to down
                                00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1,
                                changed state to down
                                00:00:50: %SYS-5-RESTART: System restarted --
                                Cisco Internetwork Operating System Software
                                IOS (tm) C2600 Software (C2600-IS-M), Version 12.0(7)T, RELEASE SOFTWARE (fc2)
                                Copyright (c) 1986-1999 by cisco Systems, Inc.
                                Compiled Tue 07-Dec-99 02:21 by phanguye
                                00:00:50: %LINK-5-CHANGED: Interface BRI0/0,
                                changed state to administratively down
                                00:00:52: %LINK-5-CHANGED: Interface Ethernet0/0,
                                changed state to administratively down
                                00:00:52: %LINK-5-CHANGED: Interface Serial0/0,
                                changed state to administratively down
                                00:00:52: %LINK-5-CHANGED: Interface Ethernet0/1,
                                changed state to administratively down
                                00:00:52: %LINK-5-CHANGED: Interface Serial0/1,
                                changed state to administratively down
                                00:00:53: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0,
                                changed state to down
                                00:00:53: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/1,
                                changed state to down
                                Router>
                                Router>enable
                                Router#copy startup-config running-config
                                Destination filename [running-config]?
                                1324 bytes copied in 2.35 secs (662 bytes/sec)
                                Router#
                                00:01:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:1,
                                changed state to down
                                00:01:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:2,
                                changed state to down
                                Router#configure terminal
                                Enter configuration commands, one per line. End with CNTL/Z.
                                Router(config)#enable secret < password > [Choose a strong password with at least one capital letter, one number, and one special character.]
                                Router(config)#^Z
                                00:01:54: %SYS-5-CONFIG_I: Configured from console by console
                                Router#show ip interface brief

                                Interface IP-Address OK? Method Status Protocol
                                Ethernet0/0 10.200.40.37 YES TFTP administratively down down
                                Serial0/0 unassigned YES TFTP administratively down down
                                BRI0/0 193.251.121.157 YES unset administratively down down
                                BRI0/0:1 unassigned YES unset administratively down down
                                BRI0/0:2 unassigned YES unset administratively down down
                                Ethernet0/1 unassigned YES TFTP administratively down down
                                Serial0/1 unassigned YES TFTP administratively down down
                                Loopback0 193.251.121.157 YES TFTP up up
                                Router#configure terminal
                                Enter configuration commands, one per line. End with CNTL/Z.
                                Router(config)#interface Ethernet0/0
                                Router(config-if)#no shutdown
                                Router(config-if)#
                                00:02:14: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
                                00:02:15: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0,
                                changed state to up
                                Router(config-if)#interface BRI0/0
                                Router(config-if)#no shutdown
                                Router(config-if)#
                                00:02:26: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down
                                00:02:26: %LINK-3-UPDOWN: Interface BRI0/0:2, changed state to down
                                00:02:26: %LINK-3-UPDOWN: Interface BRI0/0, changed state to up
                                00:02:115964116991: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0/0,
                                TEI 68 changed to up
                                Router(config-if)#^Z
                                Router#
                                00:02:35: %SYS-5-CONFIG_I: Configured from console by console
                                Router#copy running-config startup-config
                                Destination filename [startup-config]?
                                Building configuration...
                                [OK]
                                Router#show version
                                Cisco Internetwork Operating System Software
                                IOS (tm) C2600 Software (C2600-IS-M), Version 12.0(7)T, RELEASE SOFTWARE (fc2)
                                Copyright (c) 1986-1999 by cisco Systems, Inc.
                                Compiled Tue 07-Dec-99 02:21 by phanguye
                                Image text-base: 0x80008088, data-base: 0x80C524F8

                                ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)

                                Router uptime is 3 minutes
                                System returned to ROM by abort at PC 0x802D0B60
                                System image file is "flash:c2600-is-mz.120-7.T"

                                cisco 2611 (MPC860) processor (revision 0x202) with 26624K/6144K bytes of memory.
                                Processor board ID JAB031202NK (3878188963)
                                M860 processor: part number 0, mask 49
                                Bridging software.
                                X.25 software, Version 3.0.0.
                                Basic Rate ISDN software, Version 1.1.
                                2 Ethernet/IEEE 802.3 interface(s)
                                2 Serial(sync/async) network interface(s)
                                1 ISDN Basic Rate interface(s)
                                32K bytes of non-volatile configuration memory.
                                8192K bytes of processor board System flash partition 1 (Read/Write)
                                8192K bytes of processor board System flash partition 2 (Read/Write)

                                Configuration register is 0x2142

                                Router#configure terminal
                                Enter configuration commands, one per line. End with CNTL/Z.
                                Router(config)#config-register 0x2102
                                Router(config)#^Z
                                00:03:20: %SYS-5-CONFIG_I: Configured from console by console

                                Router#show version
                                Cisco Internetwork Operating System Software
                                IOS (tm) C2600 Software (C2600-IS-M), Version 12.0(7)T, RELEASE SOFTWARE (fc2)
                                Copyright (c) 1986-1999 by cisco Systems, Inc.
                                Compiled Tue 07-Dec-99 02:21 by phanguye
                                Image text-base: 0x80008088, data-base: 0x80C524F8

                                ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)

                                Router uptime is 3 minutes
                                System returned to ROM by abort at PC 0x802D0B60
                                System image file is "flash:c2600-is-mz.120-7.T"

                                cisco 2611 (MPC860) processor (revision 0x202) with 26624K/6144K bytes of memory.
                                Processor board ID JAB031202NK (3878188963)
                                M860 processor: part number 0, mask 49
                                Bridging software.
                                X.25 software, Version 3.0.0.
                                Basic Rate ISDN software, Version 1.1.
                                2 Ethernet/IEEE 802.3 interface(s)
                                2 Serial(sync/async) network interface(s)
                                1 ISDN Basic Rate interface(s)
                                32K bytes of non-volatile configuration memory.
                                8192K bytes of processor board System flash partition 1 (Read/Write)
                                8192K bytes of processor board System flash partition 2 (Read/Write)

                                Configuration register is 0x2142 (will be 0x2102 at next reload)

                                Router#

                                Comment

                                Working...
                                X