• If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Xin chào ! Nếu đây là lần đầu tiên bạn đến với diễn đàn, xin vui lòng danh ra một phút bấm vào đây để đăng kí và tham gia thảo luận cùng VnPro.

Announcement

Collapse
No announcement yet.

công thức tình cost trong eigrp for ipv6

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • công thức tình cost trong eigrp for ipv6

    em đang tìm hieu eigrp for ipv6 em đang so sánh chúng khác nhau ra sao ,em chỉ mới biết là

    .eigrp foe ipv6 nó cấu hình trên interface và phải no shut tiến trình hoạt động
    .eigrp for ipv6 phải yêu cầu đặt router id và nó dịnh dạng theo kiểu 32 bit
    .eigrp filter list thì dung distribute-list prefix-list chứ không dung route map
    .eigrp không tự động summary mà phải sum bang tay

    em còn vài chỗ chua rõ là
    + công thức tình cost trong eigrp for ipv6 nó có khác ipv4 không
    + cách thức loadbalancing nó có vẫn dùng AD và FD dể tìm ra successor và feasible successor không

  • #2
    Chào bạn. Mình thống kê lại một số điểm khác nhau giữa EIGRP for IPV4 và EIGRP for IPv6
    1. As with OSPFv3 and RIPng EIGRP advertises networks based on interface commands
    2. You must no shut the routing process, When IPV6 is configured this action creates a routing process however this process needs to be no shut to bring it up.
    3. EIGRPv6 requires a router-id
    4. Passive interfaces are configured on the routing process only
    5. EIGRPv6 performs route filtering using only the distribute-list prefix-list command.
    6. Automatic summarisation EIGRPv6 has no equivalent to the IPV4 no auto-summary command as there is no concept of classful routing in IPv6
    7. EIGRPv6 is supported in Cisco IOS beginning 12.4(6)T

    Các chức năng không thay đổi:

    Tất cả các chức năng dưới đây thì làm việc giống IPv4 . Khi cấu hình thì thay lệnh IP thành IPv6.

    • Metric weights
    • Authentication
    • Link Bandwidth Percentage
    • Split Horizon
    • Next-hop setting
    • Hello interval and hold time config
    • Address summarisation
    • Stub networks
    • Variance
    • Most other features.

    Configuring EIGRP for IPv6
    1. Enable IPv6 unicast routing
    2. Configure EIGRP on at least one interface
    3. In the EIGRP routing process, assign a router-ID
    4. Issue the no shutdown command in the EIGRP process
    5. Use the relevant show commnads to check your config.

    Lâm Văn Tú
    Email :
    cntt08520610@gmail.com
    Viet Professionals Co. Ltd. (VnPro)
    149/1D Ung Văn Khiêm P25 Q.Bình thạnh TPHCM
    Tel: (08) 35124257 (5 lines)
    Fax (08) 35124314
    Tập tành bước đi....


    Comment

    Working...
    X